Do it yourself
Frequently asked questions about cars and motorcycles
Car tutorial (Do it yourself) Motorcycle tutorial (Do it yourself) Frequently Asked Questions

Sherco St 290 - Video guides

Sherco St 290
How to Change the Engine Oil on a Sherco ST 250?
You can perform the engine oil change procedure on the Sherco ST 290 by loosening the drain plug of the oil sump, which is located at the bottom of the …Read all…
Posted on 7 June 2026 by ScegliAuto
Sherco St 290
How do you replace the clutch of the Sherco ST 290?
To replace the clutch of the Sherco ST 290, you need to loosen the screws that secure the cover of the clutch housing: this will be located in the central …Read all…
Posted on 18 November 2025 by ScegliAuto
Sherco St 290
How do you replace the clutch of the Sherco ST 290?
The clutch replacement on the Sherco ST 290 can be done by loosening the screws that secure the casing located on the right side of the vehicle, just below the …Read all…
Posted on 15 September 2024 by ScegliAuto
Sherco St 290
How do you replace the fork of the Sherco ST 290?
In order to replace the fork of the Sherco ST 290, first you need to remove the front wheel from its housing: you will need to start by loosening the screws …Read all…
Posted on 8 May 2024 by ScegliAuto
Sherco St 290
How to Dismantle the Engine of a Sherco ST 290
To dismantle the engine of the Sherco ST 290, you need to loosen the bolts securing the engine block to its housing: to free it, you will also need to …Read all…
Posted on 19 September 2026 by ScegliAuto
Sherco St 290
How to Replace the Clutch of the Sherco ST 290?
To remove the clutch of the Sherco ST 290, loosen the screws securing the cover located on the right side of the bike. Once the screws of the cover are …Read all…
Posted on 18 September 2026 by ScegliAuto
Sherco St 290
How to Replace the Sprocket on the Sherco ST 290?
To replace the sprocket on the Sherco ST 290, loosen the screws securing the cover on the left side of the bike. Once removed, locate the underlying sprocket, …Read all…
Posted on 7 August 2026 by ScegliAuto
Sherco St 290
How to Replace the Water Pump Gasket on the Sherco ST 290
To replace the water pump gasket on the Sherco ST 290, loosen the screws securing the water pump cover, located immediately to the right of the clutch cover. …Read all…
Posted on 31 July 2026 by ScegliAuto
Sherco St 290
How to Replace the Rear Shock Absorber on the Sherco ST 300
To replace the rear shock absorber on the Sherco ST 300, loosen the central nut of the rear wheel so that it can be completely removed and the chain can be …Read all…
Posted on 29 July 2026 by ScegliAuto
Sherco St 290
How to Replace the Piston on a Sherco ST 290
To replace the piston on a Sherco ST 290, access the top of the engine. Disconnect all cables connected to the cylinder. Inside the cylinder, you will find the …Read all…
Posted on 21 July 2026 by ScegliAuto
Sherco St 290
How to Replace the Clutch on a Sherco ST 290?
To replace the clutch on a Sherco ST 290, you need to loosen the screws securing the cover located on the right side of the bike, just below the exhaust pipe. …Read all…
Posted on 13 July 2026 by ScegliAuto
Sherco St 290
How to Replace the Clutch Discs on a Sherco ST 290 2011
In this video tutorial, you will see how to dismantle and replace the clutch discs on a Sherco ST 290 motorcycle in simple steps. First, position your …Read all…
Posted on 15 June 2026 by ScegliAuto
Sherco St 290
How to Dismantle the Forks on Sherco SE - ST 290 Trial (2004)
In this video, you will learn how to dismantle the front forks on various Sherco models in Trial version, such as the SE and ST 290. First, unscrew the front …Read all…
Posted on 20 May 2026 by ScegliAuto

How to Reset the Tyre Pressure Light on the Opel Grandland X

While driving, if you notice the tyre pressure warning light coming on, first check the actual inflation pressure of the tyres and, if necessary, restore the pressures recommended by the manufacturer. After restoring the correct pressures, you need to reset the warning light that has illuminated on the instrument cluster. To do this, locate the reset button on the lower central console. Press this button and hold it down for at least 3 seconds, after which the low pressure indication will turn off.

Watch the video!


by ScegliAuto

More videos