Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. MG
    3. :
  3. Mg 3
    4. : Checks and maintenance

MG 3 - Checks and maintenance

MG 3 (2011-2023 / MK 2)
Reset TPMS on a MG 3
In today's tutorial, we can see how to reset the TPMS light, which is the tire pressure warning light, on an MG 3, second-generation restyling model produced …read all…
Posted on 18 April 2024 by ScegliAuto
MG 3 (2008-2011 / MK 1)
How to prevent the DC/CC converter of the Mg 3 from getting wet.
As seen very well in the video, the part underneath the seat got wet and as a consequence, the Mg3 car wouldn't start because the DC/CC Converter is located …read all…
Posted on 24 May 2023 by ScegliAuto
MG 3 (2011-2023 / MK 2)
Where to find vehicle identification codes in Mg 3?
The vehicle identification number, also known by the English name VIN Numbers, is written under the windshield, in the lower part and on the same side as the …read all…
Posted on 2 June 2023 by ScegliAuto
MG 3 (2011-2023 / MK 2)
How do you replace the ignition cables of the MG 3?
In order to replace the ignition cables of the MG 3 you have to open the hood, so that you have access to the components inside the engine compartment: it will …read all…
Posted on 9 August 2022 by ScegliAuto
MG 3 (2008-2011 / MK 1)
How to use the MG 3 automatic gearbox
Let's go and see the instructions in this guide that will allow us to find out how to use our MG 3 automatic gearbox. First of all, let's get in the car and …read all…
Posted on 6 July 2022 by ScegliAuto
MG 3 (2011-2023 / MK 2)
How to change the date and time of Mg 3
Let's see in this guide how to change the date and time of the MG 3, following the instructions below. First of all we get on board the car and start turning …read all…
Posted on 12 May 2024 by ScegliAuto
MG 3 (2011-2023 / MK 2)
How to reset the tire warning light in the MG 3?
In this tutorial we can see how to reset the tire warning light in the MG 3, a very simple operation, to be carried out only after restoring the correct …read all…
Posted on 29 April 2024 by ScegliAuto
Battery (1) Bushings (1) Key (3) Timing belt (1) -board computer (1) Checks and maintenance (7) Brake discs (1) Air filter (2) Cabin air filter (4) Petrol filter (1) Headlight bulb (2) Rear light bulb (1) Muffler (1) Engine oil (1) Brake pads (1) Instrument cluster (2) Radiator (1) Wheel (1) Fuse box (2)

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos