Do it yourself
Frequently asked questions about cars and motorcycles
Car tutorial (Do it yourself) Motorcycle tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Mitsubishi
    3. :
  3. L 200
    4. : Bearing

Mitsubishi L 200 - Bearing

Bearing Mitsubishi L 200 (2005-2015 / mk 2)

Mitsubishi L 200 (2005-2015 / MK 2)
How to Replace the Front Wheel Bearing on a Mitsubishi L 200
You can replace the front wheel bearing on a Mitsubishi L 200 by lifting the vehicle using a jack or ramp, ensuring the wheel is not in contact with the …Read all…
Posted on 7 June 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
How to Replace the Transmission Shaft Bearing on the Mitsubishi L 200?
To replace the transmission shaft bearing on the Mitsubishi L 200, access the underside of the vehicle where the shaft is located. It must be detached from the …Read all…
Posted on 16 October 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
How to Replace the Rear Wheel Bearing on the Mitsubishi L200?
This tutorial shows how to replace the rear wheel bearing on the Mitsubishi L200, a straightforward task that requires good manual skills. First, lift the side …Read all…
Posted on 16 September 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
Removing the Propshaft Joint and Bearing on a Mitsubishi L200
Lift the vehicle as high as possible; for this job, it is advisable to use a lift. Start by unscrewing the four bolts behind the driveshaft, as shown in the …Read all…
Posted on 10 May 2026 by ScegliAuto

Bearing Mitsubishi L 200 (1996-2005 / mk 1)

Mitsubishi L 200 (2005-2015 / MK 2)
How to Replace the Front Wheel Bearing on a Mitsubishi L 200
You can replace the front wheel bearing on a Mitsubishi L 200 by lifting the vehicle using a jack or ramp, ensuring the wheel is not in contact with the …Read all…
Posted on 7 June 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
How to Replace the Transmission Shaft Bearing on the Mitsubishi L 200?
To replace the transmission shaft bearing on the Mitsubishi L 200, access the underside of the vehicle where the shaft is located. It must be detached from the …Read all…
Posted on 16 October 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
How to Replace the Rear Wheel Bearing on the Mitsubishi L200?
This tutorial shows how to replace the rear wheel bearing on the Mitsubishi L200, a straightforward task that requires good manual skills. First, lift the side …Read all…
Posted on 16 September 2026 by ScegliAuto
Mitsubishi L 200 (1996-2005 / MK 1)
Removing the Propshaft Joint and Bearing on a Mitsubishi L200
Lift the vehicle as high as possible; for this job, it is advisable to use a lift. Start by unscrewing the four bolts behind the driveshaft, as shown in the …Read all…
Posted on 10 May 2026 by ScegliAuto
Shocks (1) Car stereo (1) Body (3) Control unit (1) Key (2) Timing belt (7) Onboard computer (2) Checks and maintenance (4) Throttle body (1) Dashboard (2) Bearing (4) Differential (2) Brake rotors (2) Headlight (1) Air filter (3) Cabin air filter (1) Diesel fuel filter (1) Oil filter (4) Clutch (2) Window switch (1) Tail light bulb (2) Instrument panel light (1) Starter motor (1) Engine oil (5) Clock (1) Door trim panel (4) Front bumper (1) Brake pads (3) Wheel (5) Fuse box (22) Side mirror (2) Warning light – error code (1) Service warning light (39) Fuel cap (2) Cylinder head (1) Center console tunnel (1) EGR valve (1) Steering wheel (1)

How to Open the Bonnet of a Toyota C-HR

To open the bonnet of a Toyota C-HR, get inside the vehicle and lift the lever with the bonnet symbol located under the steering wheel. After lifting the lever, you will notice that the bonnet rises a few centimetres. Position yourself in front of the bonnet, insert your hand into the gap, and move the small internal lever from right to left, then lift the bonnet. You can keep the bonnet open during maintenance by positioning it on the support rod. To close the bonnet, remove the support rod and let it drop back down.

Watch the video!


by ScegliAuto

More videos