Do it yourself
Frequently asked questions about cars and motorcycles
Car tutorial (Do it yourself) Motorcycle tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Mitsubishi
    3. :
  3. Lancer
    4. : Rear bumper

Mitsubishi Lancer - Rear bumper

Rear Bumper Mitsubishi Lancer (2007-2020 / mk 9)

Mitsubishi Lancer (2007-2020 / MK 9)
How to Remove the Rear Bumper of a Mitsubishi Lancer
Below are the steps to remove and replace the rear bumper of a Mitsubishi Lancer. First, open the boot and start unscrewing all the fixing screws found at the …Read all…
Posted on 25 September 2026 by ScegliAuto
Mitsubishi Lancer (2007-2020 / MK 9)
How to Remove the Rear Bumper of the Mitsubishi Lancer?
In this tutorial, you will see how to remove the rear bumper of the Mitsubishi Lancer, a very simple task. To do this, you will need a set of screwdrivers, a …Read all…
Posted on 7 October 2026 by ScegliAuto
Mitsubishi Lancer (2000-2006 / MK 8)
Instructions for Removing the Rear Bumper
To remove the rear bumper, start by opening the boot and removing the rear lights (there are two fixing screws along the inner edge); disconnect the side …Read all…
Posted on 16 February 2026 by ScegliAuto

Rear Bumper Mitsubishi Lancer (2000-2006 / mk 8)

Mitsubishi Lancer (2007-2020 / MK 9)
How to Remove the Rear Bumper of a Mitsubishi Lancer
Below are the steps to remove and replace the rear bumper of a Mitsubishi Lancer. First, open the boot and start unscrewing all the fixing screws found at the …Read all…
Posted on 25 September 2026 by ScegliAuto
Mitsubishi Lancer (2007-2020 / MK 9)
How to Remove the Rear Bumper of the Mitsubishi Lancer?
In this tutorial, you will see how to remove the rear bumper of the Mitsubishi Lancer, a very simple task. To do this, you will need a set of screwdrivers, a …Read all…
Posted on 7 October 2026 by ScegliAuto
Mitsubishi Lancer (2000-2006 / MK 8)
Instructions for Removing the Rear Bumper
To remove the rear bumper, start by opening the boot and removing the rear lights (there are two fixing screws along the inner edge); disconnect the side …Read all…
Posted on 16 February 2026 by ScegliAuto
Speaker (1) Antenna (1) Car stereo (2) Battery (3) Spark plugs (2) Key (2) A/C controls (1) Onboard computer (1) Checks and maintenance (1) Headlight (1) Tail light (1) Air filter (3) Cabin air filter (2) Fuel filter (1) Oil filter (1) Clutch (1) Accessory kit (6) Light bulb (2) Headlight bulb (5) Tail light bulb (3) Interior dome light bulb (2) Instrument panel light (1) License plate light (1) (1) Handle (2) Engine (1) Clock (2) Door trim panel (1) Front bumper (2) Rear bumper (3) Brake pads (1) Shift knob (1) Fuel pump (2) Power window switch (1) Instrument cluster (2) Radiator (1) Wheel (1) Fuse box (6) Suspension system (1) Warning light – error code (4) Tire pressure warning light (4) Service warning light (12) Fuel cap (1) Blower motor (1)

How to Reset the Tire Pressure Light on a MG ZS?

On the instrument cluster of the MG ZS, the tire pressure light that appears can be reset by inflating the tires to the correct pressure: this value will be indicated on the sticker attached to the driver's door pillar. Once the tires have been properly inflated, you can turn on the instrument cluster and navigate through the menu until you find the option that indicates tire pressure: if this screen shows the new values, the light will turn off; otherwise, you will need to drive for a few miles so that the sensors can read the new values and turn off the light afterward.

Watch the video!


by ScegliAuto

More videos