Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Peugeot
    3. :
  3. 508
    4. : How to do a complete service on a Peugeot 508

Peugeot 508 - Video tutorial

Model: Peugeot 508 MK 2 - Years 2018-2024
Part: Checks and maintenance
Operation: How to do a complete service on a Peugeot 508

In this video we see how to do a complete check-up on a Peugeot 508: we start with the pollen filter, which is located behind the driver's footwell partition. We remove the screw holding the clamp and then remove the protection under the lower part of the dashboard: with pressure we also remove the lower part under the steering wheel; from here we enter with our hand and remove the cover that covers the filter: we remove it, clean the compartment from dust and residue and replace the filter. We put the cover back on and close all the partitions we removed. Now it's time for the air filter. We open the engine hood and remove the four screws that close the cover; we replace the filter and close the cover (after cleaning the compartment, of course). Now it's time for the fuel filter. Using a small screwdriver, we open the cover by removing the electrical connector; we unscrew the four screws, change the gasket and put the new filter. We reposition it, tighten the screws and put the connector back in place. We open the oil tank cap, change the filter and obviously also the cap gasket. Then we drain the used oil into a basin (which we will then dispose of correctly at an authorized center). Now we can add the new oil. Now we reset the indicators: we press the "000" button on the instrument panel and then start the car. A countdown will start during which we must continue to hold the button. Then we press the "check" button and the interval for the next check-up will appear.


Posted on 20 April 2024 by ScegliAuto

Other guides that may interest you

    Frequently Asked Questions

    • 508 2018-2026 - How do you reset the AdBlue warning light on a Peugeot 508? Read Answer
    • 508 2010-2018 - Where is the AdBlue tank located in the Peugeot 508? Read Answer
    • 508 2010-2018 - What is the problem with the AdBlue tank on the Peugeot 508? Read Answer
    • 508 2018-2026 - What could be the cause of the window problems in the Peugeot 508? Read Answer
    • 508 2018-2026 - Why does the rear window of the Peugeot 508 no longer go up? Read Answer
    • 508 2018-2026 - What are the reasons why the Peugeot 508 SW has heating problems? Read Answer
    • 508 2018-2026 - What to do if the urea warning light comes on in the Peugeot 508? Read Answer
    • 508 2010-2018 - What do the B1003 and B1024 errors stored in the Peugeot 508 ECU mean? Read Answer
    • 508 2010-2018 - "Card not detected" error in the Peugeot 508, what does it mean? Read Answer
    • 508 2010-2018 - How much is the service of the Peugeot 508 diesel? Read Answer

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos