Do it yourself
Frequently asked questions about cars and motorcycles

Derbi Gpr 50 - Video guides

Derbi Gpr 50
How to Replace the Coolant on a Derbi GPR 50

This guide will show you how to drain and replace the coolant in the engine of the Derbi GPR 50 motorcycle. First, place the motorcycle on a stand, ensuring …Read all…
Posted on 23 February 2026 by ScegliAuto
Derbi Gpr 50
How do you replace the stator of the Derbi GPR 50?

To replace the stator of the Derbi GPR 50, you will need to loosen the screws that secure the cover of the component, which will be located on the left side of …Read all…
Posted on 23 November 2025 by ScegliAuto
Derbi Gpr 50
How do you replace the exhaust pipe of the Derbi GPR 50?

To replace the exhaust pipe on the Derbi GPR 50, you need to loosen the screws that secure the exhaust terminal to the appropriate supports, located near the …Read all…
Posted on 22 November 2025 by ScegliAuto
Derbi Gpr 50
How do you disassemble the engine of the Derbi GPR 50?

It will be possible to disassemble the engine of the Derbi GPR 50 by loosening the screws that fix it to its housing: this will be located in the lower part of …Read all…
Posted on 24 May 2025 by ScegliAuto
Derbi Gpr 50
How to Replace the Exhaust on a Derbi GPR 50?

To replace the exhaust on the Derbi GPR 50, loosen the screws that secure the exhaust end can to the supports. Once the old exhaust is freed from its supports, …Read all…
Posted on 25 September 2026 by ScegliAuto
Derbi Gpr 50
How to Reset the Service Light on a Derbi GPR 50?

To reset the Service light on a Derbi GPR 50, turn on the instrument panel by turning the key in the ignition switch: once the panel is on, access the menu by …Read all…
Posted on 18 September 2026 by ScegliAuto
Derbi Gpr 50
How to Replace the Cylinder Head Gasket on a Derbi GPR 50?

To replace the cylinder head gasket on a Derbi GPR 50, loosen the bolts securing the cylinder to the top of the engine block, removing the coil and the …Read all…
Posted on 13 September 2026 by ScegliAuto
Derbi Gpr 50
How to Dismantle the Engine of the Derbi GPR 50?

The procedure for dismantling the engine block of the Derbi GPR 50 involves loosening the screws that secure the engine cylinder to its housing, allowing it to …Read all…
Posted on 11 September 2026 by ScegliAuto
Derbi Gpr 50
Dismantling the Clutch on a Derbi GPR 50

In today's video tutorial, you will see how to dismantle and replace the clutch in simple steps on a Derbi GPR 50, but also on an Aprilia RS 50. First, remove …Read all…
Posted on 10 June 2026 by ScegliAuto
Derbi Gpr 50
How to Replace Fluids on a Derbi GPR 50?

To replace the fluids on a Derbi GPR 50, first identify an oil with the appropriate specifications. Once found, open the oil drain plug located at the bottom …Read all…
Posted on 4 June 2026 by ScegliAuto
Derbi Gpr 50
Removing the Flywheel and Stator on a Derbi GPR 50

In this video tutorial, you will learn how to remove the flywheel and stator on a Derbi GPR 50cc in simple steps. First, remove the left side cover to access …Read all…
Posted on 13 May 2026 by ScegliAuto
Derbi Gpr 50
Replacing Rear Brake Pads on a Derbi GPR 50

In today’s video, we will see the steps to remove and replace the rear brake pads on a Derbi GPR 50 motorcycle. First, unscrew the mounting bolts of the rear …Read all…
Posted on 11 May 2026 by ScegliAuto

How to Reset the Tire Pressure Light on a MG ZS?

On the instrument cluster of the MG ZS, the tire pressure light that appears can be reset by inflating the tires to the correct pressure: this value will be indicated on the sticker attached to the driver's door pillar. Once the tires have been properly inflated, you can turn on the instrument cluster and navigate through the menu until you find the option that indicates tire pressure: if this screen shows the new values, the light will turn off; otherwise, you will need to drive for a few miles so that the sensors can read the new values and turn off the light afterward.

Watch the video!


by ScegliAuto

More videos