Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Jeep
    3. :
  3. Cherokee
    4. : Rear light bulb

Jeep Cherokee - Rear light bulb

Jeep Cherokee (2013-2023 / KL, MK 5)
Replacement of the rear taillight bulb of the Jeep Cherokee
The following steps will show us how to disassemble and replace the rear headlight bulb of the Jeep Cherokee. First, we open the rear door of the trunk and …read all…
Posted on 9 April 2024 by ScegliAuto
Jeep Cherokee (1984-2001 / MK 2, XJ)
How to replace the rear bulbs in the Jeep Cherokee?
In this tutorial we can see how to disassemble the rear light of the Jeep Cherokee and replace the bulbs. It is a very simple operation, we only need a 10mm …read all…
Posted on 26 June 2022 by ScegliAuto
Jeep Cherokee (1984-2001 / MK 2, XJ)
How to replace the brake light bulbs in the Jeep Cherokee?
In this video tutorial we can see how to replace the stop bulbs in the first series Jeep Cherokee. This is a very quick and easy operation. First we open the …read all…
Posted on 13 June 2022 by ScegliAuto
Jeep Cherokee (2013-2023 / KL, MK 5)
How to replace the reverse light bulb in the Jeep Cherokee
Replacing the reverse light bulb may seem like a rather complex operation and therefore impossible to carry out independently. It actually takes a few minutes …read all…
Posted on 5 April 2024 by ScegliAuto
Jeep Cherokee (2013-2023 / KL, MK 5)
How to replace the rear light bulb on the Jeep Cherokee?
In order to replace the rear light bulbs of the Jeep Cherokee you need to open the tailgate of the luggage compartment, so that you can loosen the screws …read all…
Posted on 5 April 2024 by ScegliAuto
Jeep Cherokee (2013-2023 / KL, MK 5)
Replacing the rear light bulb on the Jeep Cherokee MK5
In today's video we will see how to remove and replace the rear light bulb on the fifth series Jeep Cherokee, following these simple steps. First of all we …read all…
Posted on 11 March 2024 by ScegliAuto
Airbags (2) Alternator (2) Shock absorbers (1) Car stereo (8) Battery (8) Spark plugs (3) Control unit (1) Key (15) Timing belt (5) V-belt (3) -board computer (30) Checks and maintenance (29) Bearing (1) Mass air flow sensor (1) Headlight (4) Tail light (3) Air filter (5) Cabin air filter (9) Diesel filter (3) Hand brake (3) Light bulb (2) Headlight bulb (13) Rear light bulb (6) Interior lights ceiling light bulb (2) Handle (2) Engine (4) Window motor (1) Starter motor (3) Gear oil (2) Engine oil (7) Door panel (11) Windshield (2) Front bumper (2) Rear bumper (2) Brake pads (4) Hydraulic pistons (2) Gear Shift Knob (1) Pump (1) Fuel pump (3) Window lift button (1) Instrument cluster (9) Radiator (3) Passenger compartment heating radiator (3) Wheel (4) Fuse box (16) Seat (3) Drive shaft (1) Parking sensors (1) Suspensions (1) Outside rearview mirror (2) Windscreen wipers (2) Central tunnel (1) Steering wheel (2)

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos