Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Jeep
    3. :
  3. Wrangler
    4. : 1987-1996 (YJ, MK 1)

Jeep Wrangler Years 1987-1996 (YJ, MK 1)

Jeep Wrangler (1987-1996 / MK 1, YJ)
How to know the fuse diagram of a Jeep Wrangler
The fuse diagram of a Jeep Wrangler related to the box located inside the passenger compartment has fuses assigned to: cigarette lighter, light switch, brake …read all…
Posted on 10 March 2024 by ScegliAuto
Jeep Wrangler (1987-1996 / MK 1, YJ)
How to replace the wheel bearing of the Jeep Wrangler.
Today we will see, in this short guide, the instructions on how to disassemble and replace the wheel bearing of the Jeep Wrangler, in simple and quick steps. …read all…
Posted on 30 June 2023 by ScegliAuto
Jeep Wrangler (1987-1996 / MK 1, YJ)
How do you remove the Jeep Wrangler gearbox?
To be able to remove the gearbox from the Jeep Wrangler, you need to access the lower part of the engine compartment, so that you have access to the fixing …read all…
Posted on 13 December 2022 by ScegliAuto
Jeep Wrangler (1987-1996 / MK 1, YJ)
What is the Jeep Wrangler fuse box?
In this video we can see the diagrams of the fuse boxes of the Jeep Wrangler and their position, useful in case we need to check the fuse of a malfunctioning …read all…
Posted on 13 August 2022 by ScegliAuto
Jeep Wrangler (1987-1996 / MK 1, YJ)
How to replace the headlight on the Jeep Wrangler?
In order to replace the headlight of the Jeep Wrangler you must first open the hood, so that you can disconnect the connector in the rear part of the …read all…
Posted on 30 June 2022 by ScegliAuto
Jeep Wrangler (1987-1996 / MK 1, YJ)
How to adjust the rear jaws of the Jeep Wrangler
In today's video tutorial we will see how to go to adjust the rear brake shoes of the Jeep Wrangler, following the instructions below. First we lift the car …read all…
Posted on 17 April 2024 by ScegliAuto
Airbags (1) Alternator (1) Loudspeaker (3) Air conditioning (1) Car stereo (8) Battery (11) Grille (1) Gearbox (3) Spark plugs (1) Soft top (1) Bodywork (2) Glove box (1) Key (17) Timing belt (3) V-belt (1) -board computer (11) Checks and maintenance (26) Throttle body (1) Dashboard (1) Bearing (2) Brake discs (2) Headlight (9) Tail light (4) Air filter (8) Cabin air filter (8) Diesel filter (1) Oil filter (4) Hand brake (1) Grille (3) Accessory Kit (3) Light bulb (3) Side turn signal light bulb (4) Headlight bulb (4) Rear light bulb (2) Interior lights ceiling light bulb (1) Antifreeze liquid (2) Dashboard light (1) License plate light (2) Third brake light (2) Handle (1) Engine (1) Starter motor (3) Gear oil (1) Brake oil (2) Engine oil (9) Power steering oil (1) Door panel (3) Front bumper (2) Rear bumper (2) Brake pads (6) Tires (2) Gear Shift Knob (6) Door (8) Instrument cluster (12) Radiator (1) Passenger compartment heating radiator (1) Wheel (3) Fuse box (9) Seat (5) Drive shaft (2) Crankshaft RPM sensor (1) Outside rearview mirror (6) Drums and shoes (1) Windscreen wipers (5) Thermostat (3) Transmission (3) EGR valve (1) Interior blower (1) Steering wheel (3)

See also:

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos