Do it yourself
| ||||
|
Land Rover Freelander - Headlight bulb
Land Rover Freelander (1997-2006 / Freelander1)
How to replace the rear headlight bulbs of the Land Rover Freelander The steps outlined in this guide will show us how to disassemble and replace the rear taillight and its bulbs on the Land Rover Freelander. First, let's move …read all… Posted on 21 February 2024 by ScegliAuto
Land Rover Freelander (1997-2006 / Freelander1)
How to change the low beam light bulb on Land Rover Freelander 1 To change the bulb on the Land Rover Freelander, we open the bonnet holding it up with the support rod, we go to the back of the headlight concerned with the …read all… Posted on 18 July 2022 by ScegliAuto
Land Rover Freelander (2006-2016 / Freelander2)
Removing the headlight of a Land Rover Free Lander 2 The video shows how to remove a headlight from a Land Rover Free Lander 2. It is not difficult to do by yourself and does not take too long. First, open the …read all… Posted on 30 March 2024 by ScegliAuto
Land Rover Freelander (1997-2006 / Freelander1)
How to replace turn signal bulbs on Freelander How to replace the headlight bulb on Freelander? Let's see how the front headlight bulbs are removed. We remove the access cover from inside the stone guard …read all… Posted on 15 February 2024 by ScegliAuto
Land Rover Freelander (2006-2016 / Freelander2)
Headlight bulb replacement In order to replace the left headlight bulb (driver's side) it is necessary to remove the battery compartment cover and move the engine air filter box …read all… Posted on 26 August 2023 by ScegliAuto Airbags (1) Car stereo (10) Battery (5) Air Vents (2) Arm (1) Gearbox (1) Spark plugs (2) Soft top (1) Bodywork (1) Key (7) Locking the trunk (1) Timing belt (13) V-belt (3) -board computer (4) Checks and maintenance (20) Dashboard (1) Bearing (1) Differential (4) Brake discs (1) Headlight (3) Tail light (2) Fog lights (1) Particulate filter (1) Air filter (7) Cabin air filter (7) Diesel filter (8) Oil filter (1) Clutch (4) Light bulb (1) Headlight bulb (5) Handle (2) Engine (1) Starter motor (1) Engine oil (2) Power steering oil (1) Door panel (7) Front bumper (1) Brake pads (1) Hydraulic pistons (1) Gear Shift Knob (7) Fuel pump (5) Door (2) Instrument cluster (6) Fuse box (4) Lock (4) Suspensions (1) Engine mount (1) Central tunnel (1) Turbine (1) EGR valve (2) Steering wheel (3) |
Handbrake adjustment on Ford EcosportFirst remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base. by ScegliAuto More videos
|
For advertising on this site Write to info@scegliauto.com
ScegliAuto is not responsible for any inaccuracy of the data in the lists. To report any inaccuracy or your business (if you own the business in question), please write to info@scegliauto.com
Number of seconds to generate the page: 0.013
(c) ScegliAuto 2024 - info@scegliauto.com - Privacy Policy VAT number: IT01247470535 |