Do it yourself
Frequently asked questions about cars and motorcycles
  1. Car
  2. :
  3. Ford
  4. :
  5. Ranger
  6. : 1993-1997 (MK 2)

Ford Ranger Years 1993-1997 (MK 2)

Ford Ranger (1993-1997 / MK 2)
Where is the fuse box of the Ford Ranger located?

To find the fuse box inside your Ford Ranger, you must follow the steps described in this new mini guide dedicated to you. First of all, you must open the …Read all…
Posted on 3 August 2025 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of Wiper Control Lever

To remove the glove compartment, take off the upper plastic trim. To avoid leaving marks, use a plastic tool to also remove the trim on the steering wheel …Read all…
Posted on 10 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Installation of Front Grille and Chrome Trim

Open the front bonnet, unscrew the fixing screws along the edge of the grille and remove the front mask (grille). Proceed to remove the indicator light and …Read all…
Posted on 9 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Engine Air Filter Replacement

Once you open the front bonnet, the engine air filter housing is located at the front left (when facing the vehicle) just behind the headlamp. The first step …Read all…
Posted on 9 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of Rear Headlamp Bulb

Remove the fixing screws of the rear lamp, located at the top of the driver's cabin, disconnect the connector attached to it and connect it to the new lamp …Read all…
Posted on 8 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Front Trim Replacement

If the front trim is broken, it can be replaced with a simple operation. Remove the fixing screws of the front trim located in the engine bay and underneath …Read all…
Posted on 8 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
How to Repair, Install, Modify or Replace a Broken Ignition Lock Cylinder

If you have any issues with the ignition lock cylinder of a Ford Ranger, this tutorial will show you how to proceed. First, disconnect the negative battery …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of External Door Handle

This tutorial shows how to repair, install, modify, or replace an external door handle on a Ford Ranger. Start by removing the cover of the internal window …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of a Side Indicator Light and Bulb

This video explains how to replace the front side indicator light and its bulb on a Ford Ranger. Using a 19 mm ratchet spanner, remove the bolt that secures …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacing the Cabin Fan Resistor

First, open the front bonnet. The cabin fan is located on the left side (when facing the engine) just below the windscreen, behind the windscreen washer …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of the External Wing Mirror

In this video, the procedure for replacing an external wing mirror (driver side) of a Ford Ranger is shown. Start by detaching the top part of the window …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of Clogged Fuel Filter

The fuel filter is located at the entrance of the fuel filler neck. To replace it, you need to remove the two screws holding the filler neck, which is …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Removal of Front Door Panel

Remove the screws located on the opening handle using a Torx spanner. Remove the armrest by taking out the screws positioned lower down. Dismantle the window …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of Tailgate Cable

To replace the cable, you only need a screwdriver and a ratchet spanner. The retaining screws for the cable are accessible on the tailgate and the bodywork. …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacement of the Electric Fuel Pump

Empty the fuel tank. Lift the vehicle on a ramp and begin disconnecting the various fuel lines and electrical cables from the tank, placing a container …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Instructions for Replacing the Front Headlight

First, open the bonnet and ensure it is securely supported. To detach the lamp holder, access between the headlight and the slam panel: pull out the lamp …Read all…
Posted on 7 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Replacing the Cabin Fan

Open the front bonnet and ensure it is securely supported. To remove the cabin fan, it is necessary to detach the coolant and windscreen washer fluid …Read all…
Posted on 6 February 2026 by ScegliAuto
Ford Ranger (1993-1997 / MK 2)
Repairing the Rear Door Handle

Remove the screws securing the rear door trim panel and take off the metal plate to access the handle. Lubricate the handle's mounting pins before unscrewing …Read all…
Posted on 6 February 2026 by ScegliAuto
Airbag (1) Car stereo (1) Battery (5) Transmission (1) Control unit (1) Key (18) Trunk lock (1) Onboard computer (2) Checks and maintenance (13) Dashboard (2) Side marker light (1) Headlight (3) Tail light (2) Air filter (3) Cabin air filter (2) Fuel filter (1) Diesel fuel filter (2) Oil filter (3) Clutch (1) Grille (2) Side marker bulb (1) Headlight bulb (3) Tail light bulb (3) Interior dome light bulb (1) Handle (3) Trim cover (3) Starter motor (1) Clock (2) Door trim panel (4) Front bumper (1) Shift knob (2) Fuel pump (1) Power window switch (1) Heater control valve (2) Wheel (6) Fuse box (28) Door lock (1) Side mirror (2) AdBlue warning light (13) Warning light – error code (12) (6) Service warning light (59) Windshield wipers (1) EGR valve (2) Blower motor (2) Side window (3)

See also:

How to Replace the External Wing Mirror on a Ford C MAX

In the event of a breakage, it will be necessary to replace the external wing mirror on the 2011 Ford C MAX. This operation is easily performed independently. Start by removing the internal cover of the mirror with a plastic lever. Then, use a socket wrench to remove the securing pins. Once the pins are removed, you can take off the mirror, but not before disconnecting the power connectors. Then proceed to fit the new mirror. First, connect the connectors and then secure the mirror to its housing with the pins. Refit the plastic cover and test the operation of the electric mirror using the controls.

Watch the video!


by ScegliAuto

More videos