Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Honda
    3. :
  3. Cr V
    4. : Dashboard

Honda CR-V - Dashboard

Honda CR-V (2002-2007 / MK 2)
Where is the OBD port of the Honda CR V located?
In this new mini guide of ours, we will discover where the OBD port of your Honda CR V second series (year 2002-2006) is located. Before proceeding, however, …read all…
Posted on 25 April 2024 by ScegliAuto
Honda CR-V (1995-2001 / MK 1)
How to remove the dashboard of the Honda CR-V
Let's see in this guide the main steps that will allow us to disassemble and replace the dashboard and its parts of the Honda CR-V. First we open the front …read all…
Posted on 12 April 2024 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
Dashboard instrument block replacement
Remove the panel exactly under the steering wheel to disconnect the connectors of the various instruments. Now with a torx insert go to unscrew the bolts on …read all…
Posted on 19 September 2023 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
Portable satellite navigator installation
Unhook the cap in the center of the dashboard, just above the central console air vents; therefore also unhook the air vents and the socket connected to them. …read all…
Posted on 7 July 2023 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
Application of the internal briar effect finishes
It is possible to apply adhesive plates to the interior finishes of the dashboard, or rather the internal door moldings, to embellish and enhance the …read all…
Posted on 4 July 2023 by ScegliAuto
Airbags (2) Shock absorbers (7) Antenna (1) Car stereo (19) Anti roll bar (2) Roof Rack Bars (3) Battery (10) Coil (1) Arm (6) Spark plugs (4) Bodywork (10) Wheel rim (1) Key (14) Locking the trunk (1) Timing belt (4) -board computer (20) Checks and maintenance (49) Dashboard (5) Gearshift gaiter (1) Bearing (2) Mass air flow sensor (2) Differential (2) Brake discs (4) Headlight (8) Tail light (4) Fog lights (5) Air filter (14) Cabin air filter (14) Petrol filter (2) Diesel filter (5) Oil filter (4) Grille (2) Accessory Kit (20) Light bulb (9) Headlight bulb (8) Rear light bulb (2) Interior lights ceiling light bulb (5) Antifreeze liquid (2) Dashboard light (2) License plate light (4) Third brake light (2) Handle (2) Muffler (1) Engine (1) Window motor (1) Starter motor (1) Gear oil (2) Engine oil (13) Door panel (7) Windshield (1) Front bumper (3) Rear bumper (1) Brake pads (3) Hydraulic pistons (1) Tires (9) Gear Shift Knob (2) Pump (4) Fuel pump (2) Push button (2) Instrument cluster (16) Radiator (3) Passenger compartment heating radiator (1) Fuse box (12) Seat (1) Crankshaft RPM sensor (2) Parking sensors (2) Lock (1) Suspensions (1) Outside rearview mirror (7) Interior rearview mirror (2) Manufacturer's coat of arms (1) Windscreen wipers (12) Engine head (3) Transmission (1) Central tunnel (1) Valve (2) EGR valve (1) Interior blower (1) Side window (1) Steering wheel (6)

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos