Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Honda
    3. :
  3. Cr V
    4. : Steering wheel

Honda CR-V - Steering wheel

Honda CR-V (2007-2012 / MK 3)
How to disassemble the steering wheel of the Honda CR-V
Today's instructions will show us how to disassemble and replace the steering wheel of the Honda CR-V, in simple and quick steps. First, we get into the car …read all…
Posted on 21 March 2024 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
How to remove the steering wheel on the Honda CR-V?
In this tutorial we can see how to disassemble the steering wheel in the Honda CR-V, a very simple and quick operation. Before doing this, in order to avoid …read all…
Posted on 20 March 2024 by ScegliAuto
Honda CR-V (2012-2017 / MK 4)
How to top up the power steering fluid?
If we want to carry out a do-it-yourself maintenance on the power steering system and in particular check the oil level on the small tank, we can refer to the …read all…
Posted on 28 May 2022 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
How to replace the upper and lower steering fairing in a Honda CR-V
To replace the upper and lower steering fairing in a Honda CR-V you must first remove the small press-fit cover, which is located under the steering wheel …read all…
Posted on 2 October 2023 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
Wheel replacement and calibration
Open the panel immediately under the steering wheel to disconnect the 2 airbag connectors, using a plastic lever. Now with a torx wrench we are going to remove …read all…
Posted on 19 September 2023 by ScegliAuto
Honda CR-V (2007-2012 / MK 3)
Flying removal and assembly
Remove the flap located just under the steering wheel where the connectors to be disconnected are present, now with a torx insert we are going to unscrew the …read all…
Posted on 18 September 2023 by ScegliAuto
Airbags (2) Shock absorbers (7) Antenna (1) Car stereo (19) Anti roll bar (2) Roof Rack Bars (3) Battery (10) Coil (1) Arm (6) Spark plugs (4) Bodywork (10) Wheel rim (1) Key (14) Locking the trunk (1) Timing belt (4) -board computer (20) Checks and maintenance (49) Dashboard (5) Gearshift gaiter (1) Bearing (2) Mass air flow sensor (2) Differential (2) Brake discs (4) Headlight (8) Tail light (4) Fog lights (5) Air filter (14) Cabin air filter (14) Petrol filter (2) Diesel filter (5) Oil filter (4) Grille (2) Accessory Kit (20) Light bulb (9) Headlight bulb (8) Rear light bulb (2) Interior lights ceiling light bulb (5) Antifreeze liquid (2) Dashboard light (2) License plate light (4) Third brake light (2) Handle (2) Muffler (1) Engine (1) Window motor (1) Starter motor (1) Gear oil (2) Engine oil (13) Door panel (7) Windshield (1) Front bumper (3) Rear bumper (1) Brake pads (3) Hydraulic pistons (1) Tires (9) Gear Shift Knob (2) Pump (4) Fuel pump (2) Push button (2) Instrument cluster (16) Radiator (3) Passenger compartment heating radiator (1) Fuse box (12) Seat (1) Crankshaft RPM sensor (2) Parking sensors (2) Lock (1) Suspensions (1) Outside rearview mirror (7) Interior rearview mirror (2) Manufacturer's coat of arms (1) Windscreen wipers (12) Engine head (3) Transmission (1) Central tunnel (1) Valve (2) EGR valve (1) Interior blower (1) Side window (1) Steering wheel (6)

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos