Do it yourself
Frequently asked questions about cars and motorcycles
Car tutorial (Do it yourself) Motorcycle tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Peugeot
    3. :
  3. 206
    4. : Cylinder head

Peugeot 206 - Cylinder head

Cylinder Head Peugeot 206 (1998-2012 / mk 1)

Peugeot 206 (1998-2012 / MK 1)
How to Install the Cylinder Head on the Peugeot 206
Below are the main instructions that will allow you to install the cylinder head on the engine block of the Peugeot 206. In this case, the installation of the …Read all…
Posted on 23 August 2026 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
How to Replace the Head Gasket on the Peugeot 206?
The procedure for replacing the head gasket on the Peugeot 206 involves loosening the screws that secure the coils and spark plugs at the top of the engine …Read all…
Posted on 19 September 2026 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
How to Remove the Cylinder Head from a Peugeot 206 1.4
This video tutorial shows how to remove the engine cylinder head and its gasket from a Peugeot 206 with a 1.4 petrol engine. First, open the bonnet and start …Read all…
Posted on 23 August 2026 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Cylinder Head Gasket Repair
The cylinder head gasket ensures that the coolant, oil, and combustion gases do not come into contact with each other, preventing leakage. Overheating is the …Read all…
Posted on 16 February 2026 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Replacement of the Engine Cylinder Head Gasket
The operation of replacing the gasket is very delicate and requires special equipment, so it is recommended for experienced individuals. Start by removing all …Read all…
Posted on 12 February 2026 by ScegliAuto
Cigarette lighter (2) Airbag (9) Alternator (10) Speaker (5) Shocks (3) Antenna (5) Air conditioning (2) Car stereo (11) Anti-roll bar (2) Roof rack bars (1) Battery (17) Ignition coil (3) Air vents (4) Bushings (1) Control arm (2) Transmission (10) Spark plugs (7) Glow plugs (2) Convertible top (7) Carburetor (1) Body (8) Control unit (2) Key (26) Trunk lock (1) Timing belt (22) V-belt (6) Air conditioner (2) A/C controls (5) Onboard computer (10) Checks and maintenance (56) Dashboard (3) Shifter boot (2) Bearing (2) Brake rotors (2) Side marker light (1) Headlight (24) Tail light (6) Fog lights (6) Air filter (16) Cabin air filter (8) Fuel filter (5) Diesel fuel filter (11) Oil filter (9) Parking brake (3) Clutch (10) Grille (1) Fuel injectors (7) Reverse light switch (1) Accessory kit (1) Light bulb (7) Side marker bulb (1) Headlight bulb (24) Tail light bulb (12) Interior dome light bulb (6) Antifreeze coolant (2) Instrument panel light (15) License plate light (4) (1) Handle (1) Exhaust muffler (1) Trim cover (1) Engine (1) Power window motor (1) Starter motor (10) Transmission fluid (4) Brake fluid (1) Engine oil (9) Clock (17) Door trim panel (28) Front bumper (5) Rear bumper (4) Brake pads (4) Hydraulic pistons (1) Tires (2) Shift knob (14) Pump (8) Fuel pump (14) Car door (7) Push button (2) Power window switch (4) Instrument cluster (10) Radiator (6) Heater core (8) Wheel (4) Fuse box (58) Seat (14) Axle shaft (1) Crankshaft position sensor (1) Engine coolant temperature sensor (4) Parking sensors (1) Door lock (3) Brake system (1) Suspension system (3) Side mirror (16) Rearview mirror (3) Warning light – error code (16) Service warning light (38) Windshield wipers (3) Thermostat (2) Cylinder head (5) Tie rods (2) Center console tunnel (2) Valve (2) EGR valve (1) Blower motor (7) Side window (1) Steering wheel (6)

How to Connect the Cables to the Battery of the Citroen Xsara Picasso?

In this tutorial, you will see how to connect the cables to the battery of the Citroen Xsara Picasso, useful if you need to recharge it or perform an emergency start. First, ensure the key is not inserted, then open the bonnet and move to the front of the left headlamp. Next, locate the bolt just behind the filter box and connect the positive terminal clamp to it. Now you can connect the negative terminal to any point on the chassis, such as the indicated point. Once the operation is complete, ensure you disconnect the negative first and then the positive.

Watch the video!


by ScegliAuto

More videos