Do it yourself
Frequently asked questions about cars and motorcycles
Car Tutorial (Do it yourself) Motorcycle Tutorial (Do it yourself) Frequently Asked Questions
  1. Car
    2. :
  2. Peugeot
    3. :
  3. 206
    4. : Injectors

Peugeot 206 - Injectors

Peugeot 206 (1998-2012 / MK 1)
How to replace the fuel injector on Peugeot 206?
Below we can find the instructions and the various steps necessary to disassemble the injectors on the car: first of all it is necessary to disassemble the …read all…
Posted on 21 November 2022 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Replace the injectors on Peugeot 206 1.4
Have we encountered any problems with our vehicle? We want to remove the injectors of the Peugeot 206 car. Let's see how they are removed. We lift the front …read all…
Posted on 14 January 2024 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
How to remove the injectors of a Peugeot 206
Before starting, we will have to open the front hood of the battery, thus obtaining the necessary space to work. So let's start by removing the entire air …read all…
Posted on 30 December 2023 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Indirect check of injector efficiency
There is an indirect method to check the efficiency of the injectors by checking the amount of diesel fuel in recovery: if the injectors are functioning and …read all…
Posted on 17 August 2023 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Car injectors replacement
The following guide shows you how to replace the injectors in your car. The injectors are the evolution of the fuels that were used before and that have been …read all…
Posted on 9 August 2023 by ScegliAuto
Peugeot 206 (1998-2012 / MK 1)
Injector rail disassembly instructions
the injector rail is placed immediately under the intake manifold and fixed to the monobloc by means of bolted plastic tabs; in the video, the disassembly is …read all…
Posted on 7 August 2023 by ScegliAuto
Cigarette Lighter (2) Airbags (6) Alternator (6) Loudspeaker (3) Shock absorbers (3) Antenna (2) Air conditioning (1) Car stereo (11) Anti roll bar (1) Roof Rack Bars (1) Battery (8) Coil (3) Air Vents (4) Bushings (1) Arm (2) Gearbox (6) Spark plugs (7) Glow plugs (2) Soft top (4) Carburetor (1) Bodywork (1) Control unit (4) Key (16) Locking the trunk (1) Timing belt (17) V-belt (4) Air conditioning (1) Air conditioning controls (2) -board computer (10) Checks and maintenance (55) Dashboard (2) Bearing (2) Brake discs (2) Headlight (15) Tail light (5) Fog lights (4) Air filter (11) Cabin air filter (7) Petrol filter (5) Diesel filter (9) Oil filter (7) Hand brake (2) Clutch (5) Injectors (6) Reverse gear switch (1) Accessory Kit (1) Light bulb (7) Side turn signal light bulb (1) Headlight bulb (18) Rear light bulb (8) Interior lights ceiling light bulb (3) Antifreeze liquid (1) Dashboard light (14) License plate light (3) Third brake light (1) Muffler (1) Mask (1) Engine (1) Window motor (1) Starter motor (8) Gear oil (3) Engine oil (7) Door panel (23) Front bumper (3) Rear bumper (2) Brake pads (4) Tires (2) Gear Shift Knob (11) Pump (7) Fuel pump (13) Door (2) Push button (1) Window lift button (3) Instrument cluster (15) Radiator (5) Passenger compartment heating radiator (6) Wheel (4) Fuse box (34) Seat (9) Drive shaft (1) Crankshaft RPM sensor (1) Coolant temperature sensor (3) Lock (1) Lambda sensor (1) Suspensions (3) Outside rearview mirror (13) Interior rearview mirror (2) Windscreen wipers (1) Thermostat (2) Engine head (4) Steering rods (1) Central tunnel (1) Valve (1) EGR valve (1) Interior blower (5) Steering wheel (5)

Handbrake adjustment on Ford Ecosport

First remove the plastic profile at the base of the gear lever. To do this, slightly widen the side edges and carefully lift it to release it. There is no need to remove it completely, just move it forward to avoid bother. Now remove the plastic center console around the handbrake by first working from the rear to release it and lifting it until the brake lever passes. Also in this case it is not necessary to remove it completely but, paying attention to the connected cables, it can be stowed in front of the passenger seat. At this point we notice that at the base of the handbrake lever, on the front, we find a nut. By acting on it, with a 10 wrench, we can adjust the brake force, increasing it by turning the nut clockwise, or decreasing it by turning it counterclockwise. Once adjusted, the center console can be repositioned first, pressing lightly to engage it, and then the profile of the gearbox base.

Watch the video!


by ScegliAuto

More videos